Skip to main content

Belkin F7D1301 Wireless Router Firmware

Belkin F7D1301 Wireless Router Firmware

The Belkin N150 Wireless Home Network Router, F7D1301 allows your desktop computers, laptops and other wired or wireless devices to access the Internet easily.   

Updating your wireless router’s firmware fixes the previous version's bugs and improves its functionality.  This action must be done especially if you start experiencing connectivity issues with your device.  This article will provide you firmware updates for your Belkin F7D1301 Wireless Router
Belkin F7D1301





Download the latest firmware for Belkin N150 F7D1301 here:


https://drive.google.com/open?id=0B4tJp0pisGKLSGh0R1ZuazBNSXM
 Version Info
Firmware Version
F9K1009_WW_1.00.09
Boot Version
V1.0.0
Hardware
F9K1009 v1

IMPORTANT:  You need to remember the following:
  • Before starting the troubleshooting process, make sure that your computer is connected to the router using an Ethernet cable for stable connection to prevent upgrade failures.  Upgrading the firmware wirelessly may cause permanent damage to the router due to unstable connection during the process.
  • It is important to back up your router's setting before updating the firmware. .
To manually upgrade the firmware of your Belkin router, you need to complete the following steps:




Checking the firmware version of your router

The firmware version of your router must be identified to check whether it is outdated or needs to be re-flashed (upgrading the firmware with the same version that you are currently using).

NOTE:  The model number and version of your router can be found on the label at the bottom of the router or on the box above the UPC code.  


Downloading the firmware
Before updating the firmware of your router, you will need to download and save the updated firmware file from the Belkin Support site to your computer.  If you encounter problems in downloading your router's firmware, you may use another browser or clear the cache of your browser.  
 
QUICK TIP:  Belkin routers have the Save/Backup Settings and Restore Previous Settings features which allow you to save your current router configuration settings and to retrieve a previously backed up configuration.  
Performing the upgrade
The router's firmware can be upgraded through its web-based setup page.

Step 1:
Access the web-based setup page by opening any web browser.  On the address bar, enter your router's local IP address.
 


NOTE:  The Belkin router's default IP address is 192.168.2.1.  If this doesn't work, check your router's IP address. 
Step 2:
Click Login at the top-right corner of the page.



Step 3:
Enter your router's Password if you have one.  Otherwise, leave the field blank then click Submit.



Step 4:
On the Utilities  in the left navigation panel, click Firmware Update.



Step 5:
Click Browse... and search for the file you saved previously.



NOTE:  For Mac® computers, downloaded files are usually saved in the Downloads folder.

Step 6:
Select the firmware file and click Open.

NOTE:  The firmware version in the image below is just an example.  Your file name will vary depending on your router's model and version number.
 


Step 7:
Click Update.

 


Step 8:
You will be prompted to continue with the upgrade.  Click OK.

 


Step 9:
A prompt that advises you NOT to turn off or reboot the router at the end of the upgrade will appear.  Click OK.

 


The firmware update status will then appear.

IMPORTANT:  Make sure that you DO NOT INTERRUPT OR UNPLUG THE ROUTER during the update process.

 

 
Step 10:
Once the update is complete, you will be prompted to wait for several seconds.

 


Step 11:
Click OK after the router is done rebooting.

NOTE:  If you experience failure or see an error message when updating the firmware, powercycle your router and computer before running the update again.  If this doesn't work, repeat the same process on another computer to further isolate the issue.  If the issue still persists, reset the router to factory defaults and run the update again.

You should now have successfully updated the firmware of the Belkin router.  If the Internet connection is lost after upgrading the firmware, you will need to restore the configuration that was previously set on the router.


Comments

Popular posts from this blog

Course Syllabus: Advanced Linux System Administration and Networking

Course Outline Advanced Linux System Administration and Networking
Introduction  LinkLinux FoundationLinux Foundation TrainingLaboratory ExercisesDistribution DetailsLinux Networking Concepts and ReviewOSI Model Introduction and Upper LayersOSI Model Transport LayerOSI Model Network LayerOSI Model Lower LayersNetwork TopologyDomain Name SystemSystem ServicesManaging System ServicesNetwork ConfigurationRuntime Network ConfigurationBoot Time Network ConfigurationIntro to OpenVPNNetwork Troubleshooting and MonitoringNetwork TroubleshootingClient-Side TroubleshootingServer-Side TroubleshootingNetwork MonitoringRemote AccessRemote Access HistoryIntro to CryptographySecure Remote AccessRemote GraphicsDomain Name ServiceOverview Of DNSBIND (named) ServerBIND Zone ConfigurationHTTP ServersApacheApache ConfigurationApache Virtual HostsApache SecurityAdvanced HTTP ServersMod RewriteMod AliasMod StatusMod IncludeMod PerlPerformance ConsiderationsEmail ServersEmail OverviewPostfixDovecotFile Shar…

Networking: HP Switches Firmware Downloads

Download all HP Switches Latest Firmware here:

https://h10145.www1.hp.com/Downloads/ProductsList.aspx?lang=en&cc=il&prodSeriesId=3963985

Please contact Techeia.com or comment below if you need any assistance to upgrade your firmware.



OR
Select your product link below:

HP Switch 2520-24-PoE(J9138A)
https://h10145.www1.hp.com/Downloads/SoftwareReleases.aspx?ProductNumber=J9138A&lang=en&cc=il&prodSeriesId=3963985

HP ProCurve 1810G - 24 GE PROCURVE J9450A
https://h10145.www1.hp.com/Downloads/SoftwareReleases.aspx?ProductNumber=J9450A&lang=en&cc=il&prodSeriesId=3963985


Other HP switch models included in the above link are:
JH103AHP FF 12916E Switch ChassisJH104AHP FF 12900E Main Processing UnitJH255AHP FF 12908E Switch ChassisJH262AHP FF 12904E Switch ChassisJH263AHP FF 12904E Main Processing UnitJD238CHP 7510 Switch ChassisJD239CHP 7506 Switch ChassisJD240CHP 7503 Switch ChassisJD242CHP 7502 Switch ChassisJH207AHP 7500 1.2T Fabric IRF-only MPUJH208AHP 7502 Ma…

Visio Stencils for Cisco Switches and Routers

This is to provide the direct link to download visio stencils of various cisco products. Please comment if you are unable to get the visio stencil for a specific product. We will update the stencils and provide you with a direct link.

Please use the Following links to download visio stencils for the Cisco Routers and Switches.

http://www.cisco.com/c/en/us/products/visio-stencil-listing.html

Application Networking Services


Application Control Engine-ACE XML Gateway (ZIP - 105 KB)  11/Jun/2008


Application Networking Services-Wide Area Application Engine (ZIP - 2 MB)  15/Jan/2008


Cisco WAAS (ZIP - 911 KB)  12/Jun/2012 Cisco Interfaces and Modules


Interfaces and Modules-HWIC (ZIP - 40 KB)  14/Jan/2008


Modules-Line Cards (ZIP - 1 MB)  21/May/2009


Modules-Network Modules (ZIP - 1 MB)  22/Aug/2003


Modules-Port Adaptors (ZIP - 674 KB)  08/Oct/2003


Modules-Shared Port Adapters(SPA) (ZIP - 2 MB)  18/Dec/2008


Modules-VICs (ZIP - 117 KB)  13/Mar/2003


Modules-WICs (ZIP - 94 KB)  12/Mar/2003


Power Systems - C…